loading

Jerrytape - Professional custom tapes manufacturer & supplier to global tape brand wholesalers.

Installation Process of TPE Waterproof Joint Tape

Jerrytape - TPE joint tape manufacturer
×
Installation Process of TPE Waterproof Joint Tape

Installation Process of TPE Waterproof Joint Tape
The core principle of TPE Expansion Joint Tape is that the two side flanges are fixed to the base layer with epoxy adhesive, and the central displacement zone remains free and non adhesive, allowing the joint to open or close while sealing and waterproofing.
 
Installation Process of TPE Waterproof Joint Tape 1
construction method
 
1. Substrate preparation
•  The base surface is solid, clean, dust-free, oil-free, and free of loose animals.
•  Concrete defects should be treated with repair mortar first.
•  Construction temperature ≥ 5 ℃, avoid construction on rainy days/high humidity before drying.
2. Apply adhesive
•  Apply epoxy adhesive/cement-based waterproof slurry on both sides of the seam.
•  The width of the coating is greater than or equal to 10mm wider than the edge of the tape.
•  Thickness of approximately 1-2mm.
•  No glue is applied in the middle of the seam, leaving an elastic zone.(Key control points)
3. Laying adhesive tape
•  Press the non-woven fabric face down into the wet adhesive.
•  The middle TPE area spans the seam without stretching or wrinkling.
•  Use a scraper/roller to drive out bubbles.
4. Second layer coverage
•  When the first layer is still wet, apply another layer of adhesive to cover the edges of the non-woven fabric.
•  The middle TPE elastic zone is not covered.(Key control points)
5. Overlap and Node
•  Roll overlap ≥ 50mm.
•  Hot air welding or patches of the same material can be used at the joint.
•  Pre cutting of Internal and external corners to avoid stress concentration.
6.  Curing and Maintenance
•  Prevent puncture, water flushing, and trampling before solidification.
•  Maintain at room temperature for 2-3 days before soaking/tiling.
TPE Expansion Joint Tape
Installation Process of TPE Waterproof Joint Tape 2
Installation of TPE Expansion Joint Tape
Installation Process of TPE Waterproof Joint Tape 3
 
Application of TPE Expansion Joint Tape
Installation Process of TPE Waterproof Joint Tape 4
The two most common issues during construction are: firstly, the central displacement zone is mistakenly stuck, causing the tape to lose its deformation ability and leading to subsequent cracking of the covering layer; The second is that the epoxy adhesive coating is too thin or uneven, the edge anchoring is insufficient, and water seeps in from the edge. Both should be inspected as key stopping points during construction disclosure and acceptance.
TPE waterproof joint tape construction process:Substrate preparation--Adhesive application--Tape installation--Second adhesive coat--Overlap and Node--Curing and protection.
Frequently Asked Questions
Q: How should the substrate be prepared before installing TPE expansion joint tape?
A: The substrate must be dry, sound and clean, free of oil, dust and loose particles. Grinding or sandblasting is recommended, followed by dust removal. Ambient temperature should be 5–35°C.
Q: Where should the epoxy adhesive be applied? Can the central movement zone be bonded?
A: Apply two-component epoxy adhesive only to both side flanges, about 1.0–1.5 mm thick. The central movement zone must remain unbonded and free to move.
Q: How should TPE tape be spliced when longer lengths are required?
A: Overlap should generally be at least 50 mm. Use hot-air welding or a compatible cold-weld adhesive. Do not bond fabric face to fabric face.
Q: How to inspect the TPE tape after installation?
A: Check that both flanges are fully bonded with no voids or wrinkles, and the central movement zone remains free. The tape should not be over-stretched, and the joint must be watertight.
 
Our company not only produces TPE Expansion Joint Tape, but also Cloth Duct Tape,Gaffer Tape, Acrylic Foam Tape,Anti Slip Tape,Reflective Tape,Butyl Rubber Tape,Pavement Marking Tape, Glow In Dark Tape, etc,Looking forward to working with you.

prev
PVC vs PET Anti-Slip Tape – Technical Specification Comparison
What types of PVC floor marking tape are there? How to choose?
next
recommended for you
Get in touch with us
Contact us
whatsapp
Contact customer service
Contact us
whatsapp
cancel
Customer service